Road, Ramp and Outdoor Floor Heating Cables
Road, Ramp and Ground Snow Ice Protection Cables
Road, Ramp and Ground Snow Ice Protection Cables
Snow melting cables are thick series resistant cables used on concrete, asphalt and pavement surfaces. These are used during the winter season on driveways, sidewalks, pedestrian paths, ramps, bridges, parking areas, etc. for snow and ice melting. widely used. It is one of the best solutions to prevent ice from damaging roofs and gutters and injuring people.
In Series Resistance Heating Cables, the part that carries energy and the part that produces heat is the same and is a chrome-nickel wire. These cables can be produced in certain resistances. The resistance of these cables is directly proportional to their length. They are used in certain lengths depending on the desired power value, certain resistors and others and depending on the supply voltage.
There is a minimum length limitation that can be used to prevent excessive increase in current values that will pass over them. There are two types of serial resistance cable: single conductor (single line) and twin line. It is produced in a way that phase connection is made from one end of single conductor cables and neutral connection from the other end. In double conductor series resistive cables, phase and neutral connections are made from one end to provide ease of connection. It is produced in certain lengths and 50 cm width by using series resistive cables for ease of application.
The appropriate resistance must be chosen depending on the length and power to be used. Depending on the required power, temperature values and outdoor conditions; The insulation material used varies from PVC to PTFE and glass fiber for moisture-free places.
In general applications, heat loss is done by engineers and cable power is selected. Powers such as 30 watts are used in the selection of heat calculations. Cable selection should be made according to the external isolation environment conditions, temperature group. In order not to damage the cable in the event of an impact, the insulation must be selected correctly. Since the heater cable has certain resistance values, it can be a certain length for the desired power value and cannot be lengthened or shortened.
Snow Melting Cable Mattresses
SMC-S/T
SMC-S/T
Thermopads SMC-S/T : 30W / m power, single or double conductor series resistance heater cable
SMC-S / T Snow melting cables are thick cables used in concrete, asphalt and under pavement surfaces. These are used during the winter season on driveways, sidewalks, pedestrian paths, ramps, bridges, parking areas, etc. for snow and ice melting. widely used. SMC is one of the best solutions to prevent ice from damaging roofs and gutters and injuring people.
SMC-S/T-FE
smct-fe
SMC-S-FE : 30W / m power, single or double conductor, for sub-ASPHALT applications
SMC-FE Snow melting cables are thick cables that can be used directly under asphalt. They have a wide range of uses for melting snow and ice on driveways, sidewalks, ramps, roads, bridges and parking lots. The asphalt discharged from the asphalt machine generally has a temperature of 170-240˚C. SMC-FE will withstand this temperature for about 10 minutes. This cable conforms to IEC 800 Class C and the deformation force of the cable is 2000 N.
SMM-S/T
SMM-S/T
SMM-S/T : 300W / m2 OR 350 W / m2 power single or double conductor mattress
Snow melting mattresses (SMM) are a pre-designed solution for outdoor snow and ice melting applications without the need for a qualified and experienced technician.
Like snow melting cables (SMC), driveways, sidewalks, roads, ramps, etc. They are used under concrete or asphalt to melt snow or ice in winter.
SMM-S/T-FE
SMM-FE : 350W / m2 power, single or double conductor, for sub-ASFALT applications
SMC-FE Snow melting cables are thick cables that can be used directly under asphalt. They have a wide range of uses for melting snow and ice on driveways, sidewalks, ramps, roads, bridges and parking lots. Asphalt discharged from the asphalt machine generally has a temperature of 170-240˚C. SMC-FE will withstand this temperature for about 10 minutes. This cable conforms to IEC 800 Class C and the deformation force of the cable is 2000 N.
Floor Heating Cables Blankets
FHC-S/T
FHC-S/T
PDF: Thermopads_FHC_Zemin_Isitici_Kablolar_DataSheet
FHC : 17W / m power, 4.5mm / 5.3mm diameters single or double conductor
Floor heating cables (FHC) are robust and durable cables that can be buried under concrete and slab floors and are used in floor heating and snow melting applications.
UTHC-S/T
uthc
UTHC-X :10W / m power, 2.2mm / 3.3mm outer diameter single or double conductor
Laminate floor heating cables (UTHC) are an alternative to floor heating mats for ceramic, wood and laminated floors. With high heating efficiency, it is more economical than underfloor heating mattresses and fits better in irregularly shaped rooms.
PDF: Thermopads_UHTC_Seramik_Alti_Kablolar
FHM-S/T
FHM-S/T
100W-150W/m2 power, 0.5m width mattresses
Floor heating mats (FHM) are suitable for generating heat under ceramic, wooden or laminated floors in bathrooms, kitchens, hallways and rooms. Thanks to its very thin structures, it is ideal for green space and home renovation works.
PDF: Thermopads_FHM_Zemin_Istici_Silteler
LFHM
LFHM
They are heating mattresses covered with aluminum foil, specially designed for heating under wooden laminate.
LFM-X : 80W-140W/m2 power, 0.5m width mattresses
ThermoLAM is a very thin electric radiant floor heating system used on laminate, parquet and other floors. The advantage of using ThermoLAM is ease of installation and uniform heating of the laminate floor. Thanks to the special material used, it prevents the formation of hot spots or the problems of heating only some places.
